YU Qun, LIU Jiayu. On-line relay protection setting system for mine power grid considering multi-scenario operation mode[J]. Journal of Mine Automation, 2020, 46(12): 38-47. DOI: 10.13272/j.issn.1671-251x.2020100002
Citation: YU Qun, LIU Jiayu. On-line relay protection setting system for mine power grid considering multi-scenario operation mode[J]. Journal of Mine Automation, 2020, 46(12): 38-47. DOI: 10.13272/j.issn.1671-251x.2020100002

On-line relay protection setting system for mine power grid considering multi-scenario operation mode

More Information
  • Although the existing research on mine power grid relay protection setting has studied the setting methods of mine power grid relay protection under different operation modes, but it has not studied the setting method that applied in the automation system of mine power supply and dispatching. Therefore, the setting value could not be calculated in real time as the operation mode of the mine power grid changes. The new setting value can not be given to the protection that does not meet the requirements. To address the above problems, on-line relay protection setting system for mine power grid considering multi-scenario operation mode is proposed by defining the combination of a certain type of circuit breaker status on the bus power side of the outgoing line of the protection position as a mine power supply system scenario. The system uses the scenario corresponding switch state matrix to calculate the scenario area matrix and scenario network branch impedance matrix of the mine power supply system. Then the system calculates the maximum and minimum system impedance of the scenario based on the scenario area matrix and scenario network branch impedance matrix. As the change of breaker switching state or the scenario is monitored, the real-time switching state of the breaker is automatically read. The scenario class with the state change switch is found through the scenario switch information matrix. A scenario class is selected according to the number of switches in the scenario class, and the setting value of protection corresponding to the scenario class is calculated. Based on the calculation result of the setting value, it is reviewed whether the protection performance meets the requirements.If not meeting the requirements, on-line setting calculation will be carried out. If meeting the requirements, then the calculation of the scenario class will be completed, and the next scenario class will be calculated until the all scenario classes being calculated.The application results show that by communicating with the mine power supply dispatching automation system, the protection range of the on-line relay protection setting system for mine power grid considering multi-scenario operation mode can adapt to the requirements of relay protection devices in various operation modes. Moreover, the method avoids the rejection and misoperation of relay protection devices caused by the setting value not meeting the requirements after the change of operation mode.
  • Related Articles

    [1]LIU Shiyuan. Research on decoupling control method for single-phase cascade H-bridge rectifier in coal mine scenarios[J]. Journal of Mine Automation, 2024, 50(4): 159-168. DOI: 10.13272/j.issn.1671-251x.2023090089
    [2]ZHANG Hongguang, LIU Tingting, LYU Xiusha, ZHANG Ying, NIE Jianhong, LI Qing. Research on heterogeneous clustering networking protocol in 3D open-pit mine scenario[J]. Journal of Mine Automation, 2021, 47(12): 68-74. DOI: 10.13272/j.issn.1671-251x.2021070067
    [3]JIAN Yinwen, CHENG Zhijiang, CHEN Xingzhi, YANG Handi. Research on strong anti-misalignmemt methods of double-coupled LCL topology ICPT system[J]. Journal of Mine Automation, 2021, 47(1): 87-93. DOI: 10.13272/j.issn.1671-251x.2020080036
    [4]QIAN Zhuangzhuang, ZHANG Anning. Research on start control mode of multi-rope friction hoisting system of vertical shaft[J]. Journal of Mine Automation, 2019, 45(4): 13-18. DOI: 10.13272/j.issn.1671-251x.2018110063
    [5]QIU Shiguang, LI Siguang. A fault-tolerance topology of three-level four-leg NPC inverter[J]. Journal of Mine Automation, 2016, 42(10): 70-73. DOI: 10.13272/j.issn.1671-251x.2016.10.016
    [6]LI Fu. Renovation and Optimization of Operation Mode of Dual-circuit Power Supply System in Coal Mine[J]. Journal of Mine Automation, 2011, 37(7): 24-26.
    [7]JIANG Zhi-hua~, DUAN Jun-dong~, FAN Bu-jing~. Research of Operation Modes of Reserve Power Supply[J]. Journal of Mine Automation, 2009, 35(11): 124-127.
    [8]TANG Xiang. Study of the Fault Character of 3.3 kV Power System with Isolated Neutral Point[J]. Journal of Mine Automation, 2005, 31(6): 25-27.
    [9]SONG Zheng-li. The Mode of Computing Meshes of Mine Safety Based on Web Service[J]. Journal of Mine Automation, 2005, 31(5): 63-65.
  • Cited by

    Periodical cited type(7)

    1. 魏宗新,杨立民. 炼化用离心分离机的工程应用. 化工设计通讯. 2023(03): 75-78 .
    2. 袁惠新,王伟鹏,付双成,戴如昊,周发戚. 卧式螺旋卸料沉降离心机螺旋空心轴内表面磨损的研究. 流体机械. 2023(12): 9-15 .
    3. 刘丽艳,刘小康,樊东东,李昱奇,谭蔚,朱国瑞. 卧螺离心机进料分布器的流场模拟与结构优化. 天津大学学报(自然科学与工程技术版). 2021(01): 35-41 .
    4. 谈志超,刘雪东,郭文元,张炜. 卧式螺旋离心机操作参数对粉煤气化灰水分离特性的影响. 机械设计与制造. 2021(04): 11-14 .
    5. 付双成,张亚磊,姜毓圣,袁惠新. 卧螺离心机不同螺旋结构流场的数值模拟研究. 常州大学学报(自然科学版). 2020(01): 56-61 .
    6. 陈美岭,许亚茹,许忠义,李振铭,刘振兴. 聚氯乙烯干燥系统离心机出现的问题及解决方案. 盐科学与化工. 2020(01): 52-54 .
    7. 张建中,李峰,胡化增,张广浩,刘海洋. 矿用LW800卧螺离心机转鼓锥角结构优化. 流体机械. 2019(07): 11-14+38 .

    Other cited types(4)

Catalog

    Article Metrics

    Article views (65) PDF downloads (17) Cited by(11)
    Related

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return