放煤过程中液压支架顶梁动态载荷演化特征试验研究

霍昱名; 胡文硕; 高鹏; 闫川

doi:10.13272/j.issn.1671-251x.2024080001

放煤过程中液压支架顶梁动态载荷演化特征试验研究

doi: 10.13272/j.issn.1671-251x.2024080001

霍昱名^{1, 2,},
胡文硕³,
高鹏³,
闫川³

1.
太原理工大学矿业工程学院，山西太原　030024
2.
安徽省皖北煤电集团有限责任公司博士后科研工作站，安徽宿州　234000
3.
太原理工大学原位改性采矿教育部重点实验室，山西太原　030024

基金项目: 山西省基础研究计划资助项目（202103021223073）。

详细信息

作者简介:
霍昱名（1991—），男，山西平遥人，讲师，博士，主要研究方向为放顶煤开采理论与技术，E-mail：huoyuming@tyut.edu.cn

中图分类号: TD355.4
计量
- 文章访问数: 65
- HTML全文浏览量: 15
- PDF下载量: 6
- 被引次数: 0
出版历程
- 收稿日期: 2024-08-01
- 修回日期: 2024-09-28
- 网络出版日期: 2024-09-14

Experimental study on the evolution characteristics of dynamic load of hydraulic support top beam during coal caving

1.
College of Mining Engineering, Taiyuan University of Technology, Taiyuan 030024, China
2.
Postdoctoral Research Station, Anhui Province Wanbei Coal-Electricity Group Co., Ltd., Suzhou 234000, China
3.
Key Laboratory of In-Situ Property-Improving Mining of Ministry of Education, Taiyuan University of Technology, Taiyuan 030024, China

摘要

摘要: 接触式煤矸识别需要研究综放开采液压支架顶梁承载特性，但现有研究大多重点关注放煤前后的支架承载特性或在给定载荷情况下支架的力学响应特征，忽略了对放煤过程中载荷变化的深入探究。针对上述问题，搭建了放顶煤支架动态载荷相似模拟试验平台，借助散体颗粒模拟破碎煤矸块体，反演了综放工作面放煤过程，利用薄膜压力传感器采集支架顶梁压力，分析了放煤过程中顶梁动态载荷演化特征。试验结果表明：① 顶煤的放出对支架顶梁载荷产生了较为明显的影响，即随着顶煤放出，支架顶梁载荷整体呈先增大后减小最终稳定的演化规律。② 沿顶梁长度方向，支架顶梁距离掩护梁越远的位置受顶煤放出的影响越小，主要表现在距离掩护梁越远，顶梁载荷峰值相较初始值的增幅越小，且达到载荷峰值所需的时间越长。③ 沿顶梁宽度方向，由于顶煤的放出过程受到了约束边界或流动过程不均衡性的限制，顶梁不同位置的载荷峰值具有差异性，顶梁载荷峰值相较初始值的增幅最大值达到了最小值的2.4倍。
- 综放开采 /
- 煤矸识别 /
- 放顶煤 /
- 液压支架顶梁 /
- 动态载荷 /
- 相似模拟 /
- 压力传感器
Abstract: Contact coal-gangue identification requires studying the bearing characteristics of hydraulic support top beams in fully mechanized top coal caving. However, existing research primarily focuses on the bearing characteristics of supports before and after coal caving or the mechanical response characteristics of supports under given loads, neglecting an in-depth exploration of load changes during the coal caving process. To address this issue, a dynamic load similarity simulation test platform for top-coal hydraulic supports was established, using granular particles to simulate broken coal gangue. This setup simulated the coal caving process in a fully mechanized working face, and thin-film pressure sensors were employed to collect pressure data from the support top beams. The dynamic load evolution characteristics of the support top beams during the coal caving process were analyzed. The experimental results indicated: ① The caving of top coal significantly affected the load on the support top beams, demonstrating an evolution pattern where the overall load first increased, then decreased, and finally stabilized as the top coal was released. ② Along the length of the beam, the locations of the support top beams farther from the protective beam were less affected by the caving of top coal. This was primarily reflected in the smaller increase in peak load compared to the initial value at locations farther from the protective beam, as well as a longer time required to reach the peak load. ③ Along the width of the beam, due to the constraints of boundary conditions or the unevenness of the flow process during top coal caving, the peak load at different positions of the beam showed variability, with the maximum increase in peak load compared to the initial value reaching up to 2.4 times the minimum increase.
- fully mechanized top coal caving /
- coal-gangue identification /
- top coal caving /
- hydraulic support top beams /
- dynamic load /
- similarity simulation /
- pressure sensor

HTML全文

图 1 放顶煤支架动态载荷相似模拟试验平台

Figure 1. Dynamic load similarity simulation test platform for top coal caving support

下载: 全尺寸图片幻灯片

图 2 薄膜压力传感器

Figure 2. Thin-film pressure sensor

下载: 全尺寸图片幻灯片

图 3 试验前后散体颗粒分布情况

Figure 3. Distribution of granular particles before and after the experiment

下载: 全尺寸图片幻灯片

图 4 压力测区分布

Figure 4. Distribution of pressure measuring area

下载: 全尺寸图片幻灯片

图 5 一级测区支架顶梁载荷变化曲线

Figure 5. Load variation curve of support top beam in the first-level measuring area

下载: 全尺寸图片幻灯片

图 6 二级测区支架顶梁载荷变化曲线

Figure 6. Load variation curves of support top beam in the second-level measuring area

下载: 全尺寸图片幻灯片

图 7 三级测区支架顶梁载荷变化曲线

Figure 7. Load variation curves of support top beam in the third-level measuring area

下载: 全尺寸图片幻灯片

表 1 散体颗粒级配比例

Table 1. Granular particle size distribution

现场实测结果		相似模拟参数
直径/cm	占比/%	直径/cm	占比/%
(0，9]	13.83	(0，1]	14.0
(9，18]	46.31	(1，2]	46.0
(18，27]	20.34	(2，3]	20.0
(27，36]	19.52	(3，4]	20.0

下载: 导出CSV

表 2 三级测区支架顶梁载荷特征

Table 2. Load characteristics of support top beam in the third-level measuring area

测区	载荷峰值相较初始值增幅/%	载荷增大时对应的放煤时间/s	载荷增大持续时间/s
3−1	4	1.6	1.0
3−2	8	1.6	1.6
3−3	5	1.4	1.2
3−4	11	1.6	1.1
3−5	5	—	—
3−6	16	1.5	1.2
3−7	9	2.5	1.1
3−8	20	1.5	1.4

下载: 导出CSV

参考文献(21)

[1]	宋选民,朱德福,王仲伦,等. 我国煤矿综放开采40年:理论与技术装备研究进展[J]. 煤炭科学技术,2021,49(3):1-29. SONG Xuanmin,ZHU Defu,WANG Zhonglun,et al. Advances on longwall fully-mechanized top-coal caving mining technology in China during past 40 years:theory,equipment and approach[J]. Coal Science and Technology,2021,49(3):1-29.
[2]	王家臣. 我国放顶煤开采的工程实践与理论进展[J]. 煤炭学报,2018,43(1):43-51. WANG Jiachen. Engineering practice and theoretical progress of top-coal caving mining technology in China[J]. Journal of China Coal Society,2018,43(1):43-51.
[3]	刘峰,曹文君,张建明,等. 我国煤炭工业科技创新进展及“十四五” 发展方向[J]. 煤炭学报,2021,46(1):1-15. LIU Feng,CAO Wenjun,ZHANG Jianming,et al. Current technological innovation and development direction of the 14th Five-Year Plan period in China coal industry[J]. Journal of China Coal Society,2021,46(1):1-15.
[4]	刘长友,张宁波,郭凤岐,等. 特厚煤层综放煤−矸−岩放落流动的时序规律及识别方法[J]. 煤炭学报,2022,47(1):137-151. LIU Changyou,ZHANG Ningbo,GUO Fengqi,et al. Sequential rules and identification method of coal-gangue-rock caving flow in fully mechanized top-coal-caving workface of extra thick coal seam[J]. Journal of China Coal Society,2022,47(1):137-151.
[5]	王增才,张秀娟,张怀新,等. 自然γ射线方法检测放顶煤开采中的煤矸混合度研究[J]. 传感技术学报,2003,16(4):442-446. WANG Zengcai,ZHANG Xiujuan,ZHANG Huaixin,et al. The research on detection of rock content in coal rock mixture in top coal caving by natural gamma ray[J]. Journal of Transcluction Technology,2003,16(4):442-446.
[6]	王家臣,潘卫东,张国英,等. 图像识别智能放煤技术原理与应用[J]. 煤炭学报,2022,47(1):87-101. WANG Jiachen,PAN Weidong,ZHANG Guoying,et al. Principles and applications of image-based recognition of withdrawn coal and intelligent control of draw opening in longwall top coal caving face[J]. Journal of China Coal Society,2022,47(1):87-101.
[7]	单鹏飞,孙浩强,来兴平,等. 基于改进Faster R−CNN的综放煤矸混合放出状态识别方法[J]. 煤炭学报,2022,47(3):1382-1394. SHAN Pengfei,SUN Haoqiang,LAI Xingping,et al. Identification method on mixed and release state of coal-gangue masses of fully mechanized caving based on improved Faster R-CNN[J]. Journal of China Coal Society,2022,47(3):1382-1394.
[8]	WAN Lirong,WANG Jiantao,MA Dejian,et al. Study on coal gangue identification based on vibration and its adaptability to coal-caving process parameters[J]. Shock and Vibration,2023. DOI: 10.1155/2023/8345011.
[9]	李一鸣,白龙,蒋周翔,等. 基于EEMD−KPCA和KL散度的垮落煤岩识别[J]. 煤炭学报,2020,45(2):827-835. LI Yiming,BAI Long,JIANG Zhouxiang,et al. Caving coal-rock identification based on EEMD-KPCA and KL divergence[J]. Journal of China Coal Society,2020,45(2):827-835.
[10]	袁源,汪嘉文,朱德昇,等. 顶煤放落过程煤矸声信号特征提取与分类方法[J]. 矿业科学学报,2021,6(6):711-720. YUAN Yuan,WANG Jiawen,ZHU Desheng,et al. Feature extraction and classification method of coal gangue acoustic signal during top coal caving[J]. Journal of Mining Science and Technology,2021,6(6):711-720.
[11]	薛光辉,柳二猛,赵新赢,等. 基于声压信号时域特征的综放工作面煤岩性状识别方法研究[J]. 煤炭工程,2015,47(6):119-122. XUE Guanghui,LIU Ermeng,ZHAO Xinying,et al. Research of coal-rock character recognition in fully mechanized caving face based on acoustic pressure data time domain feature[J]. Coal Engineering,2015,47(6):119-122.
[12]	张锦旺,何庚,王家臣. 不同混合度下液体介入难辨别煤矸红外图像识别准确率[J]. 煤炭学报,2022,47(3):1370-1381. ZHANG Jinwang,HE Geng,WANG Jiachen. Coal/gangue recognition accuracy based on infrared image with liquid intervention under different mixing degree[J]. Journal of China Coal Society,2022,47(3):1370-1381.
[13]	丁震,常博深. 面向煤矸识别的近红外反射光谱数据预处理方法[J]. 工矿自动化,2021,47(12):93-97. DING Zhen,CHANG Boshen. Near-infrared reflectance spectrum data preprocessing method for coal gangue identification[J]. Industry and Mine Automation,2021,47(12):93-97.
[14]	吴桐,尉瑞,刘清,等. 综放工作面智能放煤工艺研究及应用[J]. 工矿自动化,2021,47(3):105-111. WU Tong,YU Rui,LIU Qing,et al. Research and application of intelligent caving technology in fully mechanized working face[J]. Industry and Mine Automation,2021,47(3):105-111.
[15]	张海鹏. 综放开采覆岩结构稳定性及支架支护阻力分析——以保德煤矿为例[J]. 煤炭科学技术,2022,50(增刊1):48-53. ZHANG Haipeng. Analysis on stability of overburden structure and support resistance in fully mechanized top coal caving mining:taking Baode coal mine as an example[J]. Coal Science and Technology,2022,50(S1):48-53.
[16]	刘长友,杨培举,吴锋锋,等. 两柱掩护式综放支架的承载特征及其对顶梁位态的影响研究[C]. 中国煤炭学会成立五十周年高层学术论坛,北京,2012:242-249. LIU Changyou,YANG Peiju,WU Fengfeng,et al. Bearing characters of two-leg sublevel caving shield support and its effect on beam state [C]. The High-level Academic Forum on the 50th Anniversary of the Establishment of China Coal Society,Beijing,2012:242-249.
[17]	SONG Zhengyang,KONIETZKY H. A particle-based numerical investigation on longwall top coal caving mining[J]. Arabian Journal of Geosciences,2019,12(18):1-18. doi: 10.1007/s12517-019-4743-z
[18]	YANG Yang,ZENG Qingliang. Impact-slip experiments and systematic study of coal gangue "category" recognition technology part I:impact-slip experiments between coal gangue mixture and top coal caving hydraulic support and the study of coal gangue "category" recognition technology[J]. Powder Technology,2021,392:224-240. doi: 10.1016/j.powtec.2021.06.055
[19]	覃洪雨. 大采高支架掩护梁外加载仿真及其疲劳寿命分析[D]. 阜新:辽宁工程技术大学,2022. QIN Hongyu. Simulation of external loading and fatigue life analysis of support beams with large mining heights[D]. Fuxin:Liaoning Technical University,2022.
[20]	袁祥. 液压支架位姿−负载耦合特性分析及感知基础研究[D]. 太原:太原理工大学,2022. YUAN Xiang. Basic research on pose-load coupling characteristics analysis and sensing of hydraulic support[D]. Taiyuan:Taiyuan University of Technology,2022.
[21]	李宏扬. 液压支架加载形式研究及其强度分析[D]. 阜新:辽宁工程技术大学,2022. LI Hongyang. Study of hydraulic support loading form and its strength analysis[D]. Fuxin:Liaoning Technical University,2022.